How to replace a broken toilet flange? A broken flange is something that can ruin your home and it’s the most common cause of leaks in toilets. Fortunately, you don’t have to call a plumber when these problems arise- we’ve got an easy guide on fixing them yourself!
In this post, we will teach you how to replace a broken toilet flange and install a new one.
What Is a Toilet Flange?
If you are a house owner, there is a good chance that you will have to deal with a toilet flange at some point. A toilet flange is the part of your plumbing that attaches your toilet to the rest of the drainage system in your home.
A toilet flange is a rubber or metal device that attaches to the bottom of the toilet and sits on the floor, providing a seal between your toilet and your floor.
It’s important for any homeowner to inspect their toilets every year, as drain pipes can corrode over time and cause leaks. If your toilet is overflowing, it might be because the flange is broken. Now it’s time to replace the toilet flange.
You can fix this! if you follow our guides below on this post, then you will be able to replace a broken flange in your own home.
You won’t need any professional help with these simple steps – just keep reading through them until they’re done being read correctly.
How to Replace a Broken Toilet Flange?
The toilet flange is an important part of the toilet system. It helps to keep water from leaking out and keeps your floor dry. When the flange begins to crack or break, it will need to be replaced as soon as possible.
Here are some handy stapes below, which can help you to change broken toilet flange.
1. First remove the toilet.
First, remove the toilet. Turn off both water lines and flush out any remaining contents from the tank with the bucket in hand to avoid costly repairs later on!
A handyman trick for sucking up all that wetness is using a shop vac or towel under your nose when inhaling deeply so as not to get covered by anything unpleasant-smelling–you know what I mean 🙂
2. Remove the nuts
Remove the nuts on each side of the base of your toilet. These are what attach it to its flange, and you might need a saw. which is ok because you are going to put in new toilet bolts and nuts.
The flange, when brand new is attached to the waste pipe. Many times, it rusts or snaps off. so, Tilt the toilet on its side and can be a bit tricky for one person in particular because they’re heavy and bulky – so you’ll want some help moving the toilet!
3. Remove Residue Wax Ring
You can use a putty knife to remove the wax ring residue from the exposed flange, and then you must inspect it. If your wood subfloor is rotted this may cause problems with water getting or remaining underneath; if so just cut out some of its surrounding areas for replacement boards and replace them with new plywood.
Next, if you need a new toilet ring, go to your local hardware store or online marketplace (like Amazon or Walmart). You’ll find several models from different suppliers. But don’t buy the cheapest one because it’s YOUR TOILET and remember every flush matters!
You’ll need new toilet mounting bolts. So, buy them at the hardware store or online marketplace (AMAZON or Walmart). New packages usually come with nuts and washers too!
4. Put the toilet on mounting bolts
Put the toilet mounting bolts in place and use wax from old rings to hold them. Then put on a replacement super ring, making sure that you have aligned it correctly with both sides of their corresponding flange holes before tightening down all four sets (top & bottom) enough. which means there are no leaks or looseness at this point!
The screw should be tight enough so that it won’t spin when you put weight on top of the flange, but don’t overdo it. If your tile or cement is old and worn out then use a hammer drill with discretion because this could damage the underlying material even more than necessary!
Set the new wax ring onto the flange on your toilet, and guide it into place so that you can line up mounting holes in both.
Make sure these two work well together by making adjustments with the bolts below before tightening them down! The super ring toilet bowl bolts allow you to adjust their location of them.
Place the wax ring onto your toilet, and press down until it seats. Next, wiggle the bowl back and forth to make sure that everything is seated properly. Cut off the bolts about 1/2 inch above your toilet’s base
Tighten the mounting bolt nuts to spin them. But be careful not to over-tighten as you will crack your porcelain toilet.
5. Finishing Stipe
Congratulations on finishing the install! Flush and check for leaks to make sure everything went well. If anything goes wrong, then read again all stapes properly and do it again. After trying a few times if it still goes wrong then call a professional plumber, and they will fix it.
What Happens If the Toilet Flange is Broken?
A toilet flange has a metal or plastic ring that holds the bowl to the floor, and when it breaks it can render your beloved appliance useless. when this fails it can render your flush less commode unusable.
If there’s rocking because of loose fittings in place then water may begin seeping out which leads only makes matters worse for those who already had some plumbing problems going on!
You need to change it as soon as possible, otherwise, you will very suffer from that. we wrote above how you can change a broken toilet flange.
Final Word For How to Replace a Broken Toilet Flange?
A toilet is a necessary part of any home. Knowing how to operate one can save you time, money, and hassle!
Installing a toilet flange is an important step in installing any bathroom. If you don’t install it properly it will suffer you. So, you have to know how to replace a broken toilet flange.
We hope these steps will be helpful. They are straightforward and won’t require any plumbing help which can save you money!
Related Posts:
2. How to Remove a Toilet Paper Holder?
3. How Long Is A Toilet Paper Roll?
4. How To Clean A Toto Toilet?