Pedal-based power meters like Fausoma Pro MX helps to open a wide range of high quality training. How? By ensuring that the rider has more than investments.
As any high-tech equipment, there are a few simple advice and recommendations to make sure you are most of your pedals and make sure as long as possible.
Why pedal-based power?
Pedal-based power counters allow the same vibration, even between multiple subjects, even from multiple subjects to use the same pedals to the mountain bike. Other power counters – miles, hub or curved / chain / chain-based – almost always limited to various standards between different types of bikes. Try to put your Gravel Center in XC on your XC bike or gravel facility in XC Crankset.
Below, we will describe the installation and technical procedures that will help you get the most accurate information possible from your power-based pedals. Again, compared to other electricity counters, these are small issues. But it is still important to watch them anyway.
What’s on a pedal-based power counter?
Let’s look at the work of the Association Pro MX to understand why the pedals are important to calibrate and calibrate.
All power counters rely on intense measuring devices, battery and other electronics combination (to communicate with the General Section, M). Where these pedals are placed in the pedal design, the pedals have a great impact on sustainability and service.
Favero manages to place all three of these elements inherent in electric pedals in stainless steel shaft. This means that the 6061-T6 aluminum pedal body is separate, electronically and easily modified.
On the contrary, the Garmin rally rely on the battery that can be changed. To access the battery section to access the battery section, there should be a connection between the battery area and archery. This means that it should be carefully kept with an additional obstacle between electronics and external environments for consistent data protection.
The key to the isolation of Favero electronic elements is the use of a rechargeable battery. This helps to eliminate power falls with changed batteries. The information breaks can cause dirty or incorrect contact between battery and pedal electronics. SRM’s X-Power uses a rechargeable battery in the same way, but unlike Assicoma Pro MX pedals, the intense sizes outside the power shaft are used. Unlike Favero, where the electronics is isolated isolated, SRM requires a connection between the interior and exterior of the Power Mili.
Switch between installation and bicycles
The installation will be slightly different between power-based pedals, but mostly consistent. Install the pedals, set a crank lever length, troop and calibrate.
Favero Assioma Pro MX Learning the shaft of the pedals and recommends you to install it first. It is important that the spindle lid and bike chain and shaft cover and the frame are important. Then press the recommended torka (30-40nm) using an open past 15 mm key. After the first installation, the pedals “wake up” and connect to a foreign power source to check the charging level.
Then connect the pedals to the Favero Assicoma application or connect a head directly by the head using Ant + or Bluetooth connection.
After combination, set the crank goal length to match the bike you use the pedals. If this is not possible through the Favero Association application if the bike is on your computer or not possible. .
When you use any bikes from the Pedals of Assicoma Pro MX, you should manually calibrate power sensors. Use the bicycle steep, bend and pedals in vertical position (one upper, one lower) or use the calibration function in the application or head section.
After installing, AssioMa Pro MX must fill in internal self-calibration before start sending any power information to the bike computer. This occurs in the first 10-15 pedal strokes (idealized and steadily pedaling) on the first walk.
Switch between different bikes
When you cross between any pedal-based strength meter, you should re-calibrate. Favero This process is simple with Favero Assicoma application, although the process can be carried out through your bike title.
Follow the same procedure installed for the first time to switch to Assioma Pro MX pedals in a different bike. This allows you to manually calibrate and correct the length of your crankle. If you use the same title or the length of crankarm is the same between bikes, these steps are unnecessary.
If it changes between bicycles, set the crook length. As mentioned above, if it is possible or if Favero is a Assioma application, it should be done in the head unit.
With Assioma Pro MX, the automatic calibration system of the Faveron will be sure that the data provided in the +/- 1 percent accuracy range, even -10 to + 55. Favero recommends that your bike recommends in a steep position or an angle or an angle and does not load in pedals to prevent calibration between the walk.
Pedal care and service
This means that keeping clean or from the outside world (seals, etc. It also guarantees the extreme use of rain, mud and dust (IP67).
It also means to serve the rest of the pedal body. Like any other energy pedal, you still need to serve service bearings and other small parts. Faero’s power meter pedal is the first power pedestrian, in fact, both electronics and the battery are the first power pedestrian. This means that there is no need to make additional inspections other than filling the battery.
Association Pro MX serving for pedals straight forward. Pedal reading should be lubricated from time to time using the set in pedales. Advanced instructions for this procedure Available from Favero.
In addition to the arrow, the service is the same as any pedal. Check the torque on the recent caps, end caps and farewell covers in front of each walk. Clean the pedal body with a wet cloth after the marches. Do not use aggressive solvents such as gasoline, gas oil and gasoline, industry, industry or comprehensive degreasers.
